Notice: Undefined offset: 8192 in /home/cubfest/public_html/photos/include/debugger.inc.php on line 112

Notice: Undefined offset: 8192 in /home/cubfest/public_html/photos/include/debugger.inc.php on line 112
FarmallCub | Cubfest Photo Gallery - Search results

 FarmallCub | Cubfest Photo Gallery

Photo host for users of the FarmallCub.com forum
Search results - "hole"
problem.JPG
Problem 184 viewsLooks like the lower threaded hole for implement attacment in the clutch housing was busted out and re-welded. Apparently it's not re-threaded. This bar was welded from the mower mount to the front end cultivator mount to stabilize the mower. brian c
dashlightthingy2.jpg
Rear of dashlight thingy, showing bracket61 viewsI have a little dashlight that appears rather professionally installed, as you can see from this pic of the bracket in rear of dash. Jim Becker says the hole was intended for the fuse holder, which was not installed in 49. models, even though the dash with the hole was used since mid 49. glassnegman
dashlightthingy1.jpg
My Dash, including dashlight60 viewsThis is my dash, from the 49, showing the barebulb dashlight in the fuseholder hole. I don't know if you can see the scratchmarks, but it would appear something fit over the top of the bare bulb, from the front side.glassnegman
PressWinch_04.JPG
Vinyl coated aircraft cable attached to press bed15 viewsI just drilled two holes and threaded the cable through and attached back to it's self with a cable clampDaveSaver
PressWinch_01.JPG
Boat winch rigged to raise and lower Hyd press bed23 viewsThis was a temporary rigging some 15 years ago to test the theory if this would work. It's still working. I bolted the winch to the press using the existing holes in the winch. I had purchased a 450 foot roll of vinyl covered aircraft cable from a yard sale so I used it for the cable. A couple of pulleys from the hardware store and some aircraft cable clamps is all it took. Works great.DaveSaver
Rockshaft.jpg
Rockshaft with the bellcrank extension from TM Tractor-you can see that the hole in the rockshaft is about the same distance from ctr of rotation.47 viewsawander
21 problem.JPG
Problem closeup40 viewsThreads for implement attach were busted out. I just replaced the whole torque tube with a used one from JP. Part was about $50. Shipping was twice that.brian c
hl 4.JPG
headlight mods30 viewsI've soldered a ground to the headlight casing. I j-b welded some styrene plastic over the original hole and mounted a wiring post in it.brian c
DSC_00014.jpg
Hole in hood28 viewsallenlook
DSC_00013.jpg
Big hole in hood26 viewsallenlook
DSC_00011.jpg
Big hole in grille26 viewsallenlook
DSCN2916 (Small).JPG
drawbar bolt holes47 viewsStans Cub
DSCN3091 (Small).JPG
Trans Level Hole41 viewsStans Cub
IMG_0224.JPG
trans oil holes313 viewsCowboy
IMG_0222.JPG
trans oil holes319 viewsCowboy
DSC00001~17.jpg
151 viewssigns of warpage between bolt holesbillyandmillie
Dec06Skating_Rink.JPG
54 viewsGood job of scraping, notice blade tilted fully forward to prevent riding on "shoes" and using the whole cutting length of bladeEZ
MIS.JPG
Detail of mounting to tractor94 viewsIt bolts into the drawbar holes. Note the taper on the end of the bushings so you can use the drawbar bolts.Cowboy
psrake5.jpg
250 viewsthe whole unitbarn_cub
006a_70_GrillHole.JPG
Grill Hole25 viewsNeed to fill and repair hole made by previous owner #1DaveSaver
104 files on 6 page(s) 1