Notice: Undefined offset: 8192 in /home/cubfest/public_html/photos/include/debugger.inc.php on line 112

Notice: Undefined offset: 8192 in /home/cubfest/public_html/photos/include/debugger.inc.php on line 112
FarmallCub | Cubfest Photo Gallery - Last additions

 FarmallCub | Cubfest Photo Gallery

Photo host for users of the FarmallCub.com forum
Home > User galleries

Last additions - User galleries
09_14_08HighWindstormdamage9700CrottingerRd_026.jpg
25 viewsBigdogOct 08, 2008
09_14_08HighWindstormdamage9700CrottingerRd_025.jpg
29 viewsBigdogOct 08, 2008
Loaded___Ready_May_2007.JPG
Loaded & Ready May 200733 viewsPeter PersonOct 08, 2008
DSCF0978.JPG
18 viewswild billOct 08, 2008
DSCF0977.JPG
13 viewswild billOct 08, 2008
DSCF0976.JPG
15 viewswild billOct 08, 2008
Copy_of_IMGP0018.JPG
381 viewsPaul_NJOct 06, 2008
IMG00110.jpg
Sneak Peek.. 17 viewsHe's back on all fours again!! 10-06-08WisconsinCubManOct 06, 2008
cadet1.jpg
My Cub Cadet 1450, right side49 viewsMy 1450 prior to restorationgeoaidanOct 04, 2008
cadet2.jpg
My Cub Cadet 1450, left side53 viewsPrior to restorationgeoaidanOct 04, 2008
steel.jpg
Steel ISO mounts made by Brian Miller39 viewsSteel ISO mounts milled by Brian Miller. Works great! geoaidanOct 04, 2008
raised2.jpg
Engine lifted out, full view42 viewsFull view of how I got the engine out. Used two winch straps to lift engine 5" out of tractor. Replaced mounts, then jacked the tractor up to the engine and bolted engine in place, then took winch straps off. geoaidanOct 04, 2008
beam.jpg
Beam17 viewsBefore I did the project, I had to reinforce my ceiling beam to support the 120 lb Kohler engine. geoaidanOct 04, 2008
brail.jpg
Bad Rails, mounts gone13 viewsThis is the bad rail that came off my 1450, left hand side. Notice the gouge. It is as deep as a quarter! The mounts are totally gone. geoaidanOct 04, 2008
grail.jpg
Good Rail, bad mounts16 viewsThis is the right hand side rail for my 1450. Mounts were gone- they were probably just 1-2 years old. geoaidanOct 04, 2008
kit.jpg
Steel ISO mount kit16 viewsSteel mount was milled by Brian Miller. The other pieces are items I purchased at Lowe's. Grade 8. geoaidanOct 04, 2008
raised.jpg
The engine raised out of my 145019 viewsIt was a bear to get this engine out. I had to take the axle out in order to get the bottom bolts out. (2 bolts were under axle) geoaidanOct 04, 2008
DSCF0909.JPG
Meeting of the minds43 viewsellens cubOct 03, 2008
DSCF0906.JPG
Billy Ray works on Ellens Cub AGAIN43 viewsellens cubOct 03, 2008
DSCF0895.JPG
Russ gives Seath tips on seting the toe in41 viewsellens cubOct 03, 2008
14447 files on 723 page(s) 501