Notice: Undefined offset: 8192 in /home/cubfest/public_html/photos/include/debugger.inc.php on line 112

Notice: Undefined offset: 8192 in /home/cubfest/public_html/photos/include/debugger.inc.php on line 112
FarmallCub | Cubfest Photo Gallery - Search results

 FarmallCub | Cubfest Photo Gallery

Photo host for users of the FarmallCub.com forum
Search results - "plate"
from bottom of pressure plate.jpg
clutch finger adj from face side236 viewsrick 48 cub
from backside of pressure plate.jpg
clutch finger adj. from back side252 viewsrick 48 cub
MVC-004S.JPG
412 Bush Hog Mower Plate329 viewsCub-Bud
LISTERS.JPG
Engine plate I made for my lister engine generator setup108 viewsCowboy
SerialNumSide.jpg
Side View w/Serial Number Plate104 viewsFarmLadyWannaB
LeftSide2.jpg
Lil -- left side109 viewsThe engine casting number on this side has an 'X' (part made in 1952) but one under the manifold has an 'R' code (for 1948). The serial number plate indicates 1948. Majority rules, so I'm sticking with that.FarmLadyWannaB
LoaderSerialNumPlate.jpg
Henderson Loader serial number plate185 viewsUnfortunately the red enamel makes it impossible to read the Model and Serial Number. I thought paint thinner would take it off, but NO. Tried a wire brush (lightly) & gave up. If this is Superpaint from the planet Krypton, I'd sure like to know where to buy it!FarmLadyWannaB
Bolt_Thru_Fender.jpg
Fender Reinforcing Plate297 viewsdon mccombs
Front_mount.jpg
The front cylinder mount53 viewsNote that I used a 1/2" bolt with a 1" collar around it, threaded into the mounting plate, with a nut beneath. this has a washer on top of the collar, to hold the "clevis" lower leg in place.awander
cub031107_sn.JPG
Serial number plate306 viewsTempest
P1010039.JPG
Ledger plates for sickle29 viewsold and new ledger platesRick Spivey
1341448851_ac114da281.jpg
1979 IH Cub 25359821 viewss/n plateboldpsi
s_Planter_003_(Medium).jpg
Planter Frame and Plates for Seed Hopper91 viewsTwo types of plates for seed hopper. One on the left is for use in single seed hopper, corn bottom. The one on the right is for the edge drop hopper, cotton bottom.Pete1941
100_4718_(Small).JPG
33 viewsLower emblem was cut in 3 pieces. Put back together with JB weld and backer plate.

Not quite finished with them.
mark55
16_24_foot_2x6_Trusses.jpg
Trusses Almost Done62 viewsAll 16 of the trusses are almost done. This is the first 24 foot section of the trusses for the pole barn and new shop roof. You can see the end that will sit on the exterior wall (by the green tarp), with knee wall frame section that will be sitting on the beam and the loose tails sitting on the roof. The loose tails will have another 8 feet gusseted into them with an end plate and foot plate to anchor to the existing roof. Rudi
SERIAL_NUMBER_PLATE.gif
Recreation of the serial number plate as found on a 1951 Cub25 viewsRecreation of the serial number plate as found on a 1951 CubShadeTree
1949_sn_plate2.gif
artwork for 1949 Serial Number Plate22 viewsShadeTree
78025_SN_PLATE.gif
1949? Serial Number plate25 viewsShadeTree
1957_Lo-Boy_SERIAL_NUMBER_PLATE.gif
1957 Lo-Boy with Rockford Clutch Serial Number Plate35 viewsShadeTree
1979_IH_Cub_SERIAL_NUMBER_PLATE.gif
1979 IH Cub serial number plate27 viewsShadeTree
91 files on 5 page(s) 1