| Last additions |
Boat winch rigged to raise and lower Hyd press bed23 viewsThis was a temporary rigging some 15 years ago to test the theory if this would work. It's still working. I bolted the winch to the press using the existing holes in the winch. I had purchased a 450 foot roll of vinyl covered aircraft cable from a yard sale so I used it for the cable. A couple of pulleys from the hardware store and some aircraft cable clamps is all it took. Works great.DaveSaverNov 04, 2005
|
|
Winch with cable going up to first pulley16 viewsI ran off a length of cable doubled it and attached it to the winch. One half dropped to the winch side of the bed and the other half over the top through two pulleys one on each side of the top of the press.DaveSaverNov 04, 2005
|
|
Aircraft cable from winch to other side20 viewsWelded a rod across the top of the press and then clamped a pulley to the rod. Did this on both sides.DaveSaverNov 04, 2005
|
|
Vinyl coated aircraft cable attached to press bed15 viewsI just drilled two holes and threaded the cable through and attached back to it's self with a cable clampDaveSaverNov 04, 2005
|
|
DTC lever.74 viewsThe lever on the hydraulic system, basically a shifter pinned to a straight bar that is pinned to the spring-return open center hydraulic valve, shown in other pics. If I don't keep the linkage greased, it doesn't return to center on its own, and will stall the tractor. Note the broken shifter #2 on right, and the beefy helper spring.glassnegmanNov 04, 2005
|
|
Converted Quadrant74 viewsThis is the converted quadrant from the original master control lever, rather tastefully done, I might add. My DTC has a super-heavy assist spring despit its rather beefy hydraulics.glassnegmanNov 04, 2005
|
|
close up of DTC valve, reservoir, and cylinder77 viewsThis is a close up view of the beefy hydraulics on my cub, something I call the "Don't Touch Control" or DTCglassnegmanNov 04, 2005
|
|
Grille ornament71 viewsA rather tasteful addition by a previous owner, the script "international" emblem was added, using appropriate clips behind the screen and all!!glassnegmanNov 04, 2005
|
|
white sticker48 viewsThe decals on my cub have white backgrounds.....is that just sun blanching or what?glassnegmanNov 04, 2005
|
|
remains of gear shifter #253 viewsThis is gear shifter #2 broken at the retainer pin. you can see the relatively small amount of healthy metal that was holding it together....such a shame, it shifted so nice about 4 times.glassnegmanNov 04, 2005
|
|
complete don't touch control system67 viewsthis is my hydraulic system, euphemistically called the don't touch control system. it seems to consist of the IHC TC pump, a long 2" cylinder, a 2 gal tank, an open center valve, and a confusing array of copper tubingglassnegmanNov 04, 2005
|
|
My Dash, including dashlight60 viewsThis is my dash, from the 49, showing the barebulb dashlight in the fuseholder hole. I don't know if you can see the scratchmarks, but it would appear something fit over the top of the bare bulb, from the front side.glassnegmanNov 04, 2005
|
|
Rear of dashlight thingy, showing bracket61 viewsI have a little dashlight that appears rather professionally installed, as you can see from this pic of the bracket in rear of dash. Jim Becker says the hole was intended for the fuse holder, which was not installed in 49. models, even though the dash with the hole was used since mid 49. glassnegmanNov 04, 2005
|
|
Confusing Piping on DTC66 viewsThis shows the rather bizarre piping arrangement on what I call my "don't touch control" systemglassnegmanNov 04, 2005
|
|
GITractorman - 1977 International Cub with Blade737 viewsgitractormanNov 04, 2005
|
|
GITractorman - 1977 International Cub 2295 viewsgitractormanNov 04, 2005
|
|
GITractorman - 1977 International Cub 1348 viewsgitractormanNov 04, 2005
|
|
CC 149 Restored by my father in 1998846 viewsgitractormanNov 04, 2005
|
|
|
|
| 27665 files on 1384 page(s) |
 |
|
|
|
|
|
|
1352 | |
|
|
|
|
|
